Knowing Plumbing Basics is Essential When Installing a Bathtub
Knowing Plumbing Basics is Essential When Installing a Bathtub
Blog Article
Right here below you will discover a bunch of very good content in relation to How to Install a Bathtub Yourself.
Mounting a bathtub isn't precisely brain surgery, however it does require solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a moderately difficult project. If the old tub is readily accessible, the project can relocate speedily; if you need to open a wall to get rid of the old bathtub as well as place the new bathtub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to leave the old tub as well as embeded in the new one. See to it you have certified on your own for the task as well as are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed task, it is far better to take into consideration employing one before you begin. Chances are you may need a specialist plumber to make tube connections.
This post will help you mount a brand-new bath tub in your restroom if you have currently acquired a new bathtub and do not need to change the plan of your previous water pipes.
Your tools and material list need to consist of the following:
Preparing for the Installment
Firstly, the sustaining frame supplied with the bath needs to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather troublesome due to the restricted access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming during this process. As soon as the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, position the tub in the needed setting. The wood boards are valuable in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bathtub until the spirit level reads level.
To set up taps, fit all-time low of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression join; then do the very same for the various other faucet.
Activate the water supply and also inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as additionally examine the overflow outlet and the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the bath tub ought to wait till the bathtub has actually been used a minimum of once as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making certain that the washers remain in place between the tap and the sink. Secure the faucet in position with the maker offered backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap ports. The former kind ought to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a rigid seal, creating the water to permeate the wall in between the bath and the tiling, leading to complications with dampness and possible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the tub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for finding the time to read our post. I beg you take the time to promote this page if you enjoyed reading it. Thanks for your time. Come back soon.
Get it sorted! Report this page